Enemy of Time: Why Does Your Weighing Sensor Get Out of Accuracy After a Year of Use?

Nov 22, 2026 Leave a message

In the field of industrial weighing, there is an extremely hidden yet deadly indicator: long-term stability.

 

Many projects have perfect data during acceptance. But six months or a year later, equipment engineers start to have headaches: "Even though there is no overload or water ingress, why did the zero point of the sensor run away on its own? No matter how hard the weighing data is adjusted, it cannot be accurate." In fact, this is not because your system is being interfered with, but because the sensor is experiencing "aging over time".

 

Today, we will delve into the microscopic world of high-precision weighing sensors, uncover the truth behind creep and metal fatigue, and see how the truly hardcore factories combat this physical aging through rigorous manufacturing processes.

 

一, The competition in the microscopic world: what are "creep" and "temperature drift"?

 

The core of a weighing sensor is an elastic body and a resistance strain gauge attached to it. When a load is applied, the elastic body undergoes microscopic deformation, and the strain gauges stretch or compress accordingly.

 

1.Creep: A physical phenomenon in which the output signal of a sensor undergoes small changes over time under a constant load (such as a tank being filled with 10 tons of material for a long time). Simply put, it means' pressing down, getting used to this weight, and the reading changes'.

 

2.Temperature drift: When the ambient temperature changes, the elastic modulus of the elastic material will change, and the thermal expansion coefficients of the strain gauge and the metal base are different. If the compensation is not sufficient, the data will jump around when the temperature changes.

 

Engineering truth: No material can completely eliminate creep. The national standard requirement for C3 level sensors is creep ≤ 0.02% F.S. within 30 minutes. But how to make this' aging 'process extremely slow and tiny? This entirely depends on the manufacturer's material science foundation and process control.

 

二, Extreme challenge of dynamic working conditions: million cycles of metal fatigue

 

If you use it on a batching scale or high-speed sorting line, sensors undergo thousands of loading and unloading cycles every day. This is called "alternating load" in material mechanics.

 

From a microscopic perspective, each loading generates stress concentration inside the metal elastomer. Long term alternating loads can cause aging of the adhesive layer of strain gauges, and even microcracks in metal elastomers, ultimately leading to sensor fracture failure (i.e. metal fatigue).

 

Poor quality materials: After hundreds of thousands of cycles, the zero point may drift completely, and even the elastomer may crack.

 

High quality materials: High strength alloy steel that has undergone special forging and heat treatment, combined with high-quality strain gauge adhesive, can easily withstand 1 million or even 10 million fatigue cycles while maintaining precision.

 

三, The 'life and death test' before leaving the factory: the quality control moat of the source factory

 

Since physical aging cannot be avoided, how can excellent manufacturers thoroughly eliminate the "unstable risks" before delivering their products to customers?

 

Taking Shandong Leheng and other source factories with large-scale capabilities as an example, the production of a high-precision sensor is not as simple as "assembling and testing to ensure accuracy". It requires a rigorous process loop:

 

1.Raw material selection and life verification

 

The strict selection of core materials and a 20% increase in service life compared to ordinary materials emphasized on LeHeng's official website is backed by extremely rigorous material mechanics testing. From the yield strength and tensile strength of steel to the coefficient of linear expansion, each batch of raw materials must undergo laboratory testing and mechanical evaluation upon entering the factory to block the "short-lived" gene from the source.

 

2.High and low temperature aging and temperature compensation (temperature drift control)

 

Warm float is not made by adjusting, it is baked. After the completion of strain gauge pasting and bridge assembly, the sensor must enter a high and low temperature aging chamber and undergo repeated cycles from -30 ℃ to+70 ℃. During this drastic change, engineers record real-time microvolt level data changes and use high-precision resistors for full temperature compensation. Only sensors with adequate compensation can maintain C3 accuracy in the harsh winter of Northeast China or the scorching heat of the south.

 

3.Full factory inspection: 100% bottom line commitment

 

The shipping process of many factories is inspection by sampling (AQL). But in the field of high-precision weighing, even a 1% defect rate is a 100% disaster if it falls on the customer's production line. LeHeng insists on full process precision calibration and 100% full inspection for shipment.

 

Each factory sensor must be tested for input/output impedance, insulation resistance, full load/no-load output, and recorded for corner error (for single point type) or consistency matching (for weighing modules). Only when each parameter is firmly stuck within the standard tolerance and stamped with the quality inspection seal, can it enter the packaging process.

 

四, Why are multi-sensor systems most afraid of "dispersion"?

 

This is a detail that many engineers overlook.

 

When a large silo (40 tons) uses four 10 ton weighing modules in parallel, if there is even a 0.1% difference in sensitivity (mV/V) or impedance between these four modules, the distribution of force on these four sensors will be severely uneven when filling the material on site. The one under heavy stress ages quickly and is prone to breakage; The "angle difference" that the instrument calls out through the junction box actually conceals the inconsistency of the hardware, which is a temporary solution rather than a root cause.

 

The real solution lies before leaving the factory: through high-precision digital compensation and strict 100% full inspection, these four sensors have extremely high consistency (minimal dispersion) at the time of leaving the factory. After on-site installation, there is no need for complex angle adjustment, and the system is naturally balanced in stress, resulting in a doubled lifespan. This is the hidden value that high-quality OEM/ODM suppliers can provide.

 

Buying sensors is essentially buying the certainty of time

 

When purchasing sensors, everyone is comparing accuracy, range, and price. But when you install it at a critical process point and don't want to be complained about by the workshop director every day for zero drift in the next three years, you will find that long-term stability is the most expensive cost of industrial grade products.

 

Send Inquiry

Send Inquiry