In the process of industrial automation, real-time weight monitoring of large storage tanks, reactors, hoppers, and silos (commonly used for inventory management, ingredient control, or liquid level estimation) is a must-have for industries such as chemical, food, and building materials.
Many project managers often focus their attention on the "accuracy parameters" of sensors during procurement (such as requiring C3 level or 0.02% F.S.). But when it came to on-site debugging, it was painfully discovered that even with the highest precision sensor, there were only 5 tons of material in the silo, but the instrument displayed 5.2 tons, and the data would "run" on its own as the temperature difference between day and night changed.
Where is the problem? Because weighing large containers is never simply about "buying a scale and placing it underneath", but rather a system engineering that includes mechanical structures, mechanical constraints, and thermodynamics. This article will delve into the core pain points and engineering solutions of the tank/silo weighing system.
一, Structural selection: Pull (suspension) vs. Compression (support)
Before building the system, the measurement method should be determined based on the physical form of the container:
Compression Weighing: This is the most mainstream method. Place the storage tank directly on the weighing module installed below its support legs, with the sensor subjected to vertical downward pressure. Suitable for the vast majority of ground storage tanks and silos. The commonly used sensors are shear beam or column type.
Tension Weighing: If the tank is suspended on a steel structure crossbeam or limited by bottom space, a tension sensor (such as an S-shaped or tension link) is used to "lift" the tank and weigh it.
Engineering pit avoidance: Whether under tension or compression, containers often have 3 or 4 support points. For 3-point support, the system is naturally static and uniformly stressed; For 4-point supports, if the ground or steel platform is not completely flat, one leg will be "suspended" or subjected to minimal force, which requires relying on the angle adjustment of the junction box or electronic calibration of the digital sensor to force leveling.
二, Mechanics dimension: Why must a "weighing module" be used instead of a bare sensor?
If you directly insert a bare sensor under the support leg of the storage tank, this scale is likely to survive for less than half a year. The professional weighing module solves three fatal mechanical problems:
Release thermal expansion and contraction (eliminate false lateral forces)
As mentioned earlier, temperature changes can cause several millimeters of thermal expansion and contraction in large metal tanks. If the leg is tightly locked, this force will cut off the sensor. Therefore, a standard module system must include: 1 fixed module+1 semi floating module+several fully floating modules. The fully floating module allows the tank to freely "slide" on a horizontal plane, ensuring that the sensor only senses vertical gravity.
Anti overturning and automatic reset
Outdoor, wind loads or earthquakes can cause significant lateral forces; In the workshop, the vibration of the mixer should not be underestimated. Good modules (such as structures with steel ball pressure heads) are equipped with anti overturning pull rods or limit bolts, which can quickly and automatically reset (shake column self reset) after slight displacement of the tank body, protecting the sensor from shear damage.
Top lifting maintenance design
This is the most easily overlooked yet most valuable detail in engineering. When it is necessary to replace or repair the sensor, the lifting bolt built into the module can slightly lift the container, allowing the sensor to be released from the stress state. This means that factories do not need to empty dozens of tons of materials or cut off process pipelines for online replacement, greatly reducing downtime costs.
三, Invisible Killer: Pipeline Stress and 'Hard Connections'
This is the easiest pit to step on at the tank weighing site. The tank is usually connected to a feed pipe, a discharge pipe, a steam pipe, and even an exhaust pipe.
If these pipelines are rigidly connected (hard pipes are directly welded), then a part of the weight of the tank will be "eaten" by the pipelines, or the pipelines will exert a huge pulling force on the tank.
Engineering countermeasures:
All pipelines connecting storage tanks must be replaced with flexible hoses (such as metal corrugated hoses, PTFE hoses) near the tank body.
If the process does not allow the use of hoses, expansion joints (expansion joints) must be added to the pipeline design.
The pipeline support must be independent of the weighing system. Never allow pipe supports to be placed on the scale body.
四, Special working conditions: dual test of explosion-proof and harsh environment
In the chemical and pharmaceutical industries, the silo environment is often accompanied by flammable and explosive gases or dust.
Explosion proof certification: Not only do instruments need to be explosion-proof, but weighing modules and junction boxes must also have corresponding explosion-proof levels (such as ATEX/IECEx gas zone 1/21, dust zone 20/22). Typically, Ex ia systems are used to restrict electrical energy entering hazardous areas through safety barriers.
Material and sealing: Food or chemical silos often require high-pressure water washing. At this point, the module with stainless steel fully welded seal (IP68/IP69K) is the only option.
五, From drawings to delivery: the power of customization and source quality control
Faced with the diverse shapes of tanks, complex support structures, and strict environmental requirements, standard spot goods often cannot be perfectly matched.
This greatly tests the supplier's OEM/ODM customization capabilities and manufacturing consistency. Taking Leheng in Shandong as an example:
Relying on more than 10 senior R&D engineers, we are able to complete the structural drawing and scheme confirmation of non nominal heavy modules based on the tank drawings provided by customers in a very short period of time (such as within one week).
On the manufacturing end, 100% full inspection and full process accuracy calibration are particularly important for multi-sensor systems. Because a silo weighing system usually consists of 3-4 sensors connected in parallel, if the impedance and sensitivity consistency between the sensors is not sufficient, on-site installation and angle adjustment will be a disaster. LeHeng's carefully selected raw materials and high consistency quality control ensure that three/four modules have excellent matching at the factory, greatly reducing the difficulty of on-site debugging.
The weighing system is a systematic 'collaborative operation'
No matter how high the C3 accuracy or digital communication capability your sensor has, if the module design cannot release lateral force, if the pipeline is hard connected and eats up gravity, or if the junction box is short circuited due to moisture, the entire system will still be instantly paralyzed.
Understanding the structural mechanics, pipeline layout, and thermal expansion compensation in silo weighing is a compulsory course for every equipment engineer and procurement decision maker. Only by doing it right in the three dimensions of mechanical installation, electrical protection, and source quality control can you truly obtain that precise, stable, and drift free weight data.

